Menu
Your Cart

BEARING 5/8' X 1/4'

BEARING 5/8' X 1/4'
Out Of Stock
BEARING 5/8' X 1/4'
R 116.00
Ex Tax: R 100.87
  • Stock: Out Of Stock
  • Model: KP100 5-8
  • Weight: 0.08kg
  • Dimensions: 20.00mm x 88.00mm x 88.00mm
  • SKU: KP100 5-8
  • UPC: 6009600402850
Pro-Tech. South African favourite for over 30 YearsBearing 5/8' OD x 1/4' ID

 

Router bit bearing

The high quality router bit bearing stands up to heavy use and can be used with other manufacturers bits.

5/8' OD x 1/4' ID

Always fit the dust cover on the bearing when replacing it.

consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection – clean and scratch free
  • Hearing protection – quality earmuffs
  • Dust masks – discard old and dirty masks
  • Gloves – for easy handling of material and hand protection
Wear Gloves Eye Protection Hearing Protection Dust Mask
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

Router Table Safety

Although most router bits are small, they can be potentially dangerous and should deserve your attention and respect.

Push blocks and safety devices1 Use push sticks or a push block to position your hands a safe distance from the router bit.

2 Use large-diameter bits only in a router table. Using bits over 25mm Ø (diameter) in a handheld router can possibly cause you to lose control of the tool and harm yourself or bystanders.

3 Always wear a dust mask as well as eye and hearing protection.

4 Take light cuts. Heavy cuts invite kickback. If necessary, move the fence closer to the bit or switch to a larger guide bearing/bush.

5 Use a featherboard (anti-kickback device) to support the workpiece against the router table and/or fence.

6 Never climb-cut. Always feed the stock from right to left. Against the rotation of the router bit. (see illustration)

7 Avoid routing small stock. Instead, rout a larger piece and cut it to size afterwards. If you absolutely have to profile a small piece, build an suitable jig or secure the workpiece.

8 Always use a guard. If the fence didn’t come with a guard, make your own.

9 Never start the router with the bit in contact with the material.

10 Don’t force the router bit or overload the router. Excessive heat is an enemy.

11 Secure/fasten the router in the base before starting/switch on the router.

Router bit to collet fit12 Don’t bottom out the bit in the collet or partially insert the bit. Instead, completely insert the bit, and then back off approximately 2 mm. At least 2/3 's of the router bit shank should be inside the collet.

13 Be sober and not under the influence of medicine that causes a lack of concentration

14 Tidy up your workshop to ensure the ability to move freely with enough room around the router table

Pro-Tech. South African favourite for over 30 Years
Description Specification
Outside diameter Ø 5/8'
Inside diameter Ø 1/4'

Write a review

Note: HTML is not translated!
Bad Good
BEARING 1/4' O.D. X 1/8' I.D.
Out Of Stock
Bearing   Router bit spare part Bearing dimensions: Unit Outside diameter Inside diameter Imperial Ø 1/4 inch ..
R 110.00
Ex Tax:R 95.65
BEARING FOR KP3503 3/4' O.D. X 3/16' I.D.
Out Of Stock
Bearing For changing cutting depthsRabbet: (răb′ĭt) also re·bate (rē′bāt′,răb′ĭt) A cut or groove along or near the edge of a piece of wood ..
R 115.00
Ex Tax:R 100.00
BEARING 3/8' O.D. X 1/8' I.D.
Out Of Stock
Bearing   Router bit spare part Bearing dimensions: Unit Outside diameter Inside diameter Imperial Ø 3/8 inch ..
R 110.00
Ex Tax:R 95.65
BEARING 3/4' O.D. X 1/4' I.D.
Out Of Stock
Bearing   Router bit spare part Bearing dimensions: Unit Outside diameter Inside diameter Imperial Ø 3/4 inch ..
R 116.00
Ex Tax:R 100.87
BEARING 1/2' O.D. X 1/4' I.D.
Out Of Stock
Bearing   Router bit spare part Bearing dimensions: Unit Outside diameter Inside diameter Imperial Ø 1/2 inch ..
R 110.00
Ex Tax:R 95.65
COVE BIT 1 1/8' X 1/2' TCT 1/4' SHANK
Out Of Stock
Edge Profile router bit Cove profile The cove router bit is an edge profile router bit that produces a concave profile on the edge of a work piece..
R 393.00
Ex Tax:R 341.74
 Single flute Straight bit In choosing a straight bit for any application, always select one with the shortest cutting edges and the shortest..
R 109.00
Ex Tax:R 94.78
 Single flute Straight bit In choosing a straight bit for any application, always select one with the shortest cutting edges and the shortest..
R 110.00
Ex Tax:R 95.65
Router bit spare parts pack   Spare parts included Allen key Bearing ID 3/16' x OD 1/2' - KP100 1-2 Bearing ID 3/16' x OD 3/8' - ..
R 179.00
Ex Tax:R 155.65
BEARING 5/8' X 1/4'
Out Of Stock
Bearing 5/8' OD x 1/4' ID   Router bit bearing The high quality router bit bearing stands up to heavy use and can be used with other manu..
R 116.00
Ex Tax:R 100.87
Retaining collar for 1/2' shaft router bits   Retaining collar The retaining collar is used to secure a bearing with an internal diameter Ø 1/2' ..
R 25.00
Ex Tax:R 21.74