![9' 230MM POLISHING BONNET WOOL 100% SHEEPSKIN 9' 230MM POLISHING BONNET WOOL 100% SHEEPSKIN](https://robotindustrial.oplcdn.co.za/image_resize.php?image_path=data/products/vermontsales/MM9-2.jpg&image_width=550&image_height=550&resize_type=fit)
9' 230MM POLISHING BONNET WOOL 100% SHEEPSKIN
R 252.00
Ex Tax: R 219.13
Quantity | Unit Price | You Save |
---|---|---|
3 or more | R 247.64 | 1.73 % |
6 or more | R 242.06 | 3.95 % |
12 or more | R 237.40 | 5.79 % |
- Stock: In Stock
- Model: MM9-2
- Weight: 0.10kg
- Dimensions: 252.00mm x 320.00mm x 34.00mm
- SKU: MM9-2
- UPC: 6009515825324
For 20 or more items, click to quote
Tie on polishing wool buff
![](images/torkcraft/polishing/mm10_sm1.jpg)
Diameter: Ø230mm
Application:
The polishing wool buff should be used with an automotive polisher. Different polishes and waxes can be used with the buff. The buff is fastened onto a rubber backing pad with laces. Make sure the diameter of the polishing buff is the same as the backing pad's diameter.
It is necessary to polish a vehicle body panel when:
- The panel has been newly painted with a clear-coat.
- Shallow scratch marks need to be removed.
- The panel has suffered from oxidation.
- Swirl marks and hologram defects need to be removed.
TIP:
The buff is washable after use if the polishing compound is soluble.
Tie on polishing wool buff range:
ORDER NO. | DIAMETER | USE BACKING PAD |
MM4 | ø100mm | |
MM5 | ø125mm | TCBP125C / PG338 |
MM6 | ø150mm | TCBP150C |
MM7 | ø180mm | PG33805 |
MM7-2 | ø180mm | PG33805 |
MM8 | ø200mm | |
MM9 | ø230mm | |
MM9-2 | ø230mm | |
MM10 | ø250mm |
Tie on polishing wool buff
Steps to take when polishing a panel:
1. Preparing the panel:
- Sometimes a panel has fine over-spray left from spraying the clear-coat. This needs to be removed by lightly sanding with a fine abrasive paper. All over-spray need to be sanded out up to P1500 grit.
- The panel should be washed when all spray-finishing defects have been removed. Any dirt particles could cause scratch marks when polishing.
- Tight curves and ends of the panel should be masked-off to prevent the effects caused by point pressure. The polisher should always be used on flat surfaces.
2. Applying the polishing compound:
- A five rand coin amount of polishing compound should be applied to the buff. Switch the polisher to it's lowest speed setting.
- Switch on the polisher and gradually spread the polishing compound over the panel.
- Keep moving the polisher on the panel to have as little amount of pressure and friction.
- The polishing compound will remove the scratch marks caused by the P1500 sand paper and it will bring out an impressive gloss finish.
- Remove the masking from the panels and apply the polishing compound to a microfiber cloth. Hand polish (by moving your hand in a small circular motion) the tight curves and ends in the panels until the same finish is achieved as from the polisher.
3. Wash the panel when finished:
- Wash the panel after polishing to remove any residue from the polishing compound.
consider safety for your health and the people around you | |||
General safety suggestions:It is advisable to always have the following items nearby and in a good condition
|
|||
![]() |
![]() |
![]() |
![]() |
Wear Gloves
|
Eye Protection
|
Hearing Protection
|
Dust Mask
|